The instructions on page 12 of the Netro sprite quick start guide says I can use the ‘remote control’ feature to on the Netro app to turn on and off the sprinklers. I can’t find a ‘remote control’ setting on this app. 

Hello, when I program the repeated watering schedules, it does not appear in the calendar and nothing happens.

The setup recommends a WiFi that is not an option in my WiFi settings. There is a Netro WiFi I can connect to, but the app refuses to recognize it, saying I have to use the name they give me. 

If I have smart watering enabled does it activate sprinklers when it (sprite) determines a need?  If so how do I prevent that when I happen to be mowing the lawn?  

I have 5 Whisperer sensors and 1 of them is no longer measuring moisture.  Temp and Lux are being measured but consistently zero on moisture.  Placed next to another functioning sensor that is reading moisture and still nothing.

Suggestions?

I set up the pixie timer, everithing seems ok but the valve does not opens, nor with program nor in manual mode, no water at all.

can you help me?

Hello,  how to establish in app the stop of irrigation schedule when rain previsión is on?

Thanks

Hi All,

I'm a satisfied Italian customer of Netro Sprite 12 zones since 2019!

Recently I set my router to shutdown the wifi during the night, the Netro sprite it's the only one device that don't automatically reconnect when wifi come up in the morning, the white LED still blinking. To reconnect at the network, I need to phisically shutdown and power on the Sprite.

Is there a "trick" or an update to cover this issue? HW Version: 1.2 , Firmware Version 1.1.3

Thanks in advance.

Giacomo

When trying to use the Pixie to manually water the garden, I go to the Netro app and select the pixie. It shows "sleeping", 99%charged. I then select "manual run" and set a time. The app then grays out and says "communicating" as the timer begins counting down my preset manual time but the valve stays closed. Why? When does it open? 

Hello,

Is there a way to get a manual schedule to honor the rain forecast and not water on those days?  I need to be on a manual schedule for one zone as I have a wide variety of plants in that zone and I have to force a shot everyday cycle.  However if it rains I would like the app to not water that zone on that day

Thank you,

Dhar

I live in Spain and ubication selector do not let me specify my correcto location. I assume It is requieres to provide the Meteorological service the place where to predict weather, so if location is incorrect, the weather too and the watering planning is not optimized properly.

Please work It out un Next app releases.

I live in Katy Texas and have been using the Netro water controller in smart mode for over 2 years with no problems.  We received at least 1.5in of rain on the April 25, so I was dismayed to find my sprinkler system watering my yard on the morning of the 26th.  The rain graph in the app is showing 0.03in for the 25th and is clearly wrong.  I have tried changing to all the different weather providers, but the total rain accumulation doesn't change.  The frontal system that caused the rain passed over the entire area, so this is not a situation of local shower only affecting a localized area.   

I am unable to have my new whisperer working. It doesn’t light on even after half a day under the sun.

Sprinklers are coming on but the ap is not showing the activity on each station. I have done a factory reset and still no luck. Help please. 

How do I allow a third-party to have control of my sprinklers? The situation would be for example if a irrigation lawn specialist is coming over to adjust my sprinkler heads and I don’t wanna have to follow him around and turn on zones etc.

I was trying to edit/delete existing schedules. But seems not working

1. There was always a green circle running when I save the change and it never go away

2. If I close the app and come back again, the calendar still show old schedule 

3 however if I try to edit the schedule now, it shows the program had been removed (as shown in pic)

In my schedule, some of my zones are showing as Smart Zones, the rest are not. They also schedule themselves in an undesirable order. How do I take control of my schedule and tell this thing to do what I want? I find this interface to be way too confusing. 

I've had the whisper sensor for about a year and it's worked great the entire time. I decided to add 2 more sensors for more zones and both of them are reporting absurd numbers more often than not. I have tried resetting them, moving them, nothing is working. Really not happy right now. Attached is a screenshot of a typical day's readings. 

Buongiorno, come si fa a programmare la centralina per innaffiare due volte in una notte ?

Why is My Netro light is blinking