My whisperer-2, installed ~36 hours ago, is consistently reporting a temp about 10F hotter than reality.

Thoughts?

Hello,

I would like to ask for advice on how to improve the water pressure for my Netro Pixie irrigation timer.

Here are the details of my setup:

• The water is stored in a cistern with a capacity of one cubic meter (1 meter x 1 meter x 1 meter), equivalent to 1,000 liters.
• The Netro Pixie smart timer is installed three meters below the tap of the cistern.
• When the timer opens, only a small amount of water flows out.

How can I improve the water output and quantity? Are there any adjustments or solutions you would recommend?

Thank you very much for your help!

Hi.

My controller operates but many times, rather than executing the time setting. It just cuts out? 

I do have a sensor connected but I took it out of the ground to exclude wet soil feedback 

I'm guessing there is a parameter forcing the stops? 

Could anyone give me a direction where to look? 

Thanks 

System went offline at 2 in the morning and I can’t get any response. Checked the outlet and it’s working. Tried to reset. Unplugged and plugged back in. Help!

Hello

My system has 5 solenoids.  All worked fine until recently.  One will turn on and off manually.  

However in smart timer it turns in but not off.  

How can I confirm if a app set up issue or a hardware issue with solenoid itself.  

Nath

How does the Spark test the valves?

I want to connect a 24V input sensor on the spark outlet channels to switch 2 knx connect valves in different location. Cabling to those valves is to long for 24V. 
The valve testing always says that there is not current and switch it off --> Do i need a resistor on the outlet to simulate a valve? If yes, which value should the resistor have?

Thanks,

Peter

Hi,

I have 4 zones and a master valve. When I run any of the zones, they won't shut off when the timer runs out. If I switch the AC power off, then the valve will shut. I have checked the valve and it has no issue with opening and closing except when the sprite is running it. I tested cables for continuity, and I have tried swapping cables with no change. My ac power pack is AC 24v.

This issue affects each of the valves but only when controlled via the sprite. The valves are fully operational otherwise.

Hoping for a fix, otherwise will return to Amazon under warranty and get another brand.

My Netro controller is about three years old. I recently changed my Wi-Fi router about two months ago.  I repaired the controller with the new Wi-Fi, all seemed to work for a few days. Then the controller started cycling on and off of Wi-Fi. There are windows of several minutes that I can communicate with the controller, then windows of several hours when I cannot.  The light on the controller is solid for about 20 seconds, then three slow blinks, solid for 20 seconds, then three slow blanks, this pattern continues indefinitely. I have repaired the controller to WiFi several times. I have unplugged and then plugged the controller back in multiple times. Nothing seems to resolve the issue. It’s frustrating when I’m changing sprinkler heads and have to wait several hours to try a manual run to test the new heads. Has anyone else experience this and more importantly solved this issue? Thanks for the help!

Seems like my system has a mind of its own.  It'll water on time for a few weeks then stop then water again. 

My controller has been out almost a month. I have factory reset, short reset uninstalled app, and unplugged it. No matter what I do, i cannot get past the connect to netro wifi step. I need to blow out my sprinklers and I cannot get my device to work to manually run them. It will say its connected and do the spinning wait thing, then suddenly tell me to connect to the netro internet again. When I go to do it again it says no internet connection. Please help me. I sent an email from my email as the registered user (husband) is deployed in the middle east. Please look for an email from "kimbo__@" 

Thanks!

I have 6 zones and all but zone 1 run.  I start running manually and app says watering but nothing.  I checked the wires, none loose.  It will run randomly but I’m getting really frustrated.  

Hello there!

I'm really hoping you can help me. I bought two Whisperer 2s.

My sensor shows the moisture way above where I have my watering adjustment set to not water, but it is still watering. What am I doing wrong?

Hi everyone!

My Whisperer Smart Plant Sensor has broken. I would like to know if it is possible to fix it by buying a replacement part or if there is a DIY solution to reuse the device.

Thank you.

Desde hace unos días la APP no está funcionando. Según la APP el WiFi está OFFLINE, pero según la página web está ONLINE. Según ambos está WATERING pero la realidad es que no está regando y no responde a órdenes. No dispongo en este momento de acceso físico al dispositivo. ¿Podrían indicarme si el problema es un problema local o de la APP/Web?

For some time the system worked perfect. Now I  have two sections that don't work. It turns out that the signal to activate the valve is too short. When I  put a meter on it and then activate the valve the meter jumps to 28v for about one second then drops to zero before the valve can move. Conversely the one that works stays at 28v for much longer. I have rebooted and reset the system.  Any ideas?

I am doing yard work to 2 of my 3 zones right now and have the whole system disabled for several days as many heads are disconnected.  Woke up a 5am to have zone 3 on and spraying water everywhere for 20 minutes. 

How is this possible? Why do you not update your softwar? 

Ho, we need support, as we are having an issue as the app doesn’t activate watering. The control unot shows E1.

Quando collego la valvola la zona resta alimentata a 24 v anche quando finisce il ciclo. Quindi non smette di irrigare anche con la spia di colore verde.

Senza la valvola invece la tensione torna 0 volt.

Cosa può essere il problema

What can I do?

Thanks