I have smart watering enabled with a preference for watering times between 1 and 7.  The schedule shows the system is running from 1 - 10 am and then again starting at 6:00 pm - 9:36.  How do I get this adjusted? My water bill was the highest it has ever been!

Hey I'm all setup and running with my sprite and things are great!

My issue is that the advanced smart waters is choosing times that are early in the morning when I shower and its reducing the water pressure for me and I'm sure the heads have less pressure coming out since I am using water too. 

Is there anyway without going to basic scheduling and making my own programs that I can edit the times in the morning it waters?

I'm doing a first installation with an 100-HV-FF 24V ACRain Bird valve.I connected the wires to the C and 1 connector to serve zone 1. I populated the zone in the app. Because I want to test the system before I disassemble my previous I did not install the valve between the pipes. I click the "play" triangle in app home screen but I get no reaction from the valve. The solenoid is completely closed. I am using the 24V AC/AC adapter bought on your website.

Does the valve need water flowing through to work properly?

Thank you

When are you planning release firmware update for sprite having issue connecting to wifi after power issue? This happens quite a bit and my sprite is off line.

I have one zone showing a watering time of 1 minute.  Is there a way to change this.  In the settings it says it waters every 2.65 days for 13.5 minutes.  It may take 30 seconds or more for the zone to come on.  Any ideas

Post install and after first unsuccessful run, it says it watered but it definitely did not, I found an extra wire that I had plugged into ‘C’ next to the ‘M’, that I had left unplugged in my last successful Netro setup. I have now unplugged it and did another unsuccessful run. My question is, when making a wiring tweak like that do I need to press the ‘RST’ before proceeding with a run?

To the Netro community:

We recently have launched an update for the Netro app on App Store and Google Play. In the newest version of the app, we allow one sensor to monitor up to 3 zones but the user needs to make sure the zones have similar environmental conditions.

Please upgrade your app to the newest version and go to Settings->Sensors, select a sensor, go to Zones and select the zones you would like to monitor.

            

            

After saving the changes, you can go to the Home page and check the topsoil moisture level of your zones reported by sensor.

Please feel free to explore other new and exciting features that we just added : 

1.Support Apple Watch

(only available for iOS )

2.Support Weather Underground PWS

(Settings->Controller->Weather Provider)

3.Rainfall adjustment

(Please go to the Discover page and tap the "+" button on the upper right corner,  select "Correct Rainfall")

Regards,

Netro Support

To the Netro community:

We recently have launched an update for the Netro app on App Store. In the newest iOS version (2.3.0) of the app, Apple Watch is now supported.

In the watch app, users will be able to check the status of the device, the weather data, zone status and view watering schedules in the next 7 days.

Please feel free to explore other new and exciting features that we just added (also available on Android) : 

1.Support Weather Underground PWS

(Settings->Controller->Weather Provider)

2.Rainfall adjustment

(Please go to the Discover page and tap the "+" button on the upper right corner,  select "Correct Rainfall")

3.Enable plant sensors to monitor multiple zones

( Settings->Sensors, select a sensor, go to Zones and select the zones you would like to monitor)

Regards,

Netro Support

 good install and was working but later lost connection... what firmware version should it have? how about a windows app ? sprite connects to tablet but claims no internet connection....   your sprite is extremely frustrating compared any other smart devices that does't ask to reset router if it loses connection looking for issues. if every device did this i would need a tech full time so i can have a life

I have two zones for the grass in my backyard and want to connect 1 whisper for both zones since its one small piece of grass.  How can I do this?

The new version is exactly as promised! I can't wait to see how it works!

I have configured my WU PWS, and setup a secondary rain guage as well! 

It's the last day of the month and the new version still hasn't dropped. You are already a month past your original commit date. Please stop marketing products that are add-ons, when the software is lagging substantially. The big companies are going to catch, kill and eat you unless you start running faster. 

I have installed several Wisper ands would Like to know what rate of water would be acceptable on surface and deep down? 

Hello, I've noticed that 2 out of my 6 zones suffer from low to no water pressure. I tried removing the nozzles to test but the water kept barely coming out. I know the solinoids are working because the water is coming from the zones, but how can I understand why there is super low pressure?

When I try to set a program for tomorrow I get this message "Program should be within the same day"

What does that mean???

Why can't I set programs for an upcoming day???

Hello, does Netro work with Hunter sprinklers - having trouble getting them to work!

During step 8, It says "Netro Connected but no internet"

Can you pleas ehelp?

When i read an answer on this forum (from the app) 

how can i return back to the previous list  of topics (without doing home button)?

name is translate with ‘prénom’ (meaning= first name) correct translation is ‘nom’

maybe you can have help from users to have a perfect translation in all languages

How do I set my program to run each zone for 30 minutes each, but water 10 minutes 3 times each.  I thought this used to be an option, but I don’t see it.